What Does All-Over Print File Prep Require?
10 Customization & ManufacturingA complete all-over print file is built per pattern piece, not per artwork panel. It needs the right resolution at final print size, a bleed and seam margin on every cut edge, and a colour mode the printer's workflow can accept without conversion surprises.
Most reprints and rejections in full-garment printing trace back to one of those three items, or to a designer supplying artwork that looks correct on a flat canvas but has never been split across the panels of a garment.
This guide sets out what an all-over print file has to contain, how panel separation changes the artwork, and where file preparation stops being able to save a design.
Key Takeaways
- Full-garment printing is cut-and-sew, so the file is prepared per panel.
- Bleed and seam margin are separate allowances and both are needed.
- Resolution is set at final print size, not at mockup size.
- Seam alignment decides whether a repeat looks continuous on the finished piece.
- A print-ready file still needs a physical strike-off before a bulk run.
What Does an All-Over Print File Have to Contain?
An all-over print file is the artwork already mapped onto the pattern pieces of a specific garment, at production size, with the allowances the sewing floor needs.
That definition carries four requirements. The file must reference a named garment and size, not a generic canvas. It must carry each panel as a separate printable area. It must include bleed beyond the cut line and an additional margin inside the seam. And it must be supplied in the colour space the printing method uses.
A flat 100 by 100 centimetre canvas does not meet any of those requirements, even when the artwork on it is excellent. Someone still has to place it on a front body, a back body, two sleeves, a collar and a hem band, and decide what happens at each seam.
Which File Specifications Matter Most?
Four specifications decide whether a file can be printed as supplied. The rest are preferences that can be corrected in prepress.
| Specification | Typical production value | Why it decides the outcome |
|---|---|---|
| Resolution at final size | 150 to 300 dpi at 1:1 scale | Upscaling from a small canvas softens edges and fine text |
| Bleed beyond cut line | 10 to 20 mm on every cut edge | Absorbs cutting tolerance and shrinkage after washing |
| Seam margin | Match the seam allowance plus a few millimetres | Keeps pattern running into the join instead of stopping short |
| Colour mode | CMYK for sublimation workflows, sRGB only by agreement | Dye sublimation shifts saturated RGB colours on polyester |
| Panel separation | One layer or file per pattern piece | Print area on a sleeve is not the same shape as a body panel |
Treat the table as a checklist rather than a target. A file that meets all five rows can go straight to a strike-off. A file that misses the first row cannot be rescued by any amount of press adjustment.
How Do Bleed and Seam Margin Differ?
Bleed and seam margin are often treated as one allowance. They protect against different failures and both are required.
Bleed extends the artwork past the cut line so that a cutting blade running slightly outside the pattern still lands on printed fabric. Without bleed, a small cutting error produces a white edge on a dark garment, which is visible on the finished piece and impossible to fix afterwards.
Seam margin extends the artwork further, past the stitch line, so the pattern continues into the join. On a side seam, a sleeve seam or a shoulder, the panel edges meet with the seam allowance folded inside. If the print stops at the cut line, the join shows a thin unprinted strip once the garment is turned through.
The correct allowance depends on the seam type. A flatlock join consumes less fabric than an overlocked seam on a heavy knit, and a hem band folds back on itself. Ask the printer for the seam allowance per seam before setting the margin, rather than applying one number to every edge.
How Does Panel Separation Change the Artwork?
Panel separation is the step that turns a design into a garment file, and it is where most all-over print file problems begin.
Each pattern piece is a different shape with a different grain direction. A motif placed vertically on the front body lands at a different angle on a sleeve once the sleeve is set in. A repeat that tiles neatly on a rectangle will not tile neatly across a curved armhole.
The practical approach is to build the repeat first, then cut the panels from it in the same coordinate space. That way the pattern flows across seams by construction rather than by manual nudging.
Mirrored panels need a decision. Printing a left and right sleeve from the same file gives a symmetrical look on one side and a reversed look on the other if the artwork is not mirrored deliberately. For directional artwork such as text or a horizon scene, this is the difference between a clean garment and an obvious error.
Our pattern team reviews panel separation against the garment's construction drawing before a file is approved, because a mistake at this stage is cheap to fix and expensive to discover on a printed roll.
What Resolution and Colour Settings Should You Use?
Set resolution at final print size and check it on the largest panel, not on a mockup.
A file built at 72 dpi on a small canvas and scaled up to a full back panel loses real detail, even if the software reports a high number after resampling. The test is simple: view the file at 100 percent at production dimensions and look at the smallest text or the finest line in the design.
For sublimation on polyester, work in CMYK and expect saturated colours to sit slightly flatter than they appear on screen. Neon and deep navy are the usual casualties. A physical strike-off on the actual fabric is the only reliable check, because the same colour file prints differently on a 150 gsm polyester and on a cotton-rich blend.
Keep type as vector where possible. Rasterised text at panel scale is where soft edges and broken strokes appear first.
Limitations: Where File Prep Cannot Help
A well-prepared all-over print file solves production problems. It does not solve design problems, and it cannot compensate for a fabric that will not hold the image.
Fine detail below the resolution of the printing method will soften regardless of how the file is built. Very light tints on a dark base cloth will read as the base colour once printed. These are limits of the process, not of the file.
Shrinkage is the second limit. A cotton-rich garment can move after the first wash, and artwork placed close to a seam can drift onto the seam allowance. Bleed covers small movement, not a fabric that shrinks outside its stated tolerance.
The third limit is cost at low volume. Preparing panel-separated files and running a strike-off is fixed work per design. On a single-piece order the prep cost can exceed the print cost, which is why most full-garment programmes start at a sample quantity rather than at one unit.
What Does the Approval Workflow Look Like?
Approval should happen on a printed piece, not on a screen.
The sequence that works is: garment and size confirmed, pattern pieces issued, artwork placed and panelled, file checked against the specification table, strike-off printed on the production fabric, and the approved strike-off retained as the reference for the bulk run.
Every step produces an artefact someone can point to later. When a reprint is requested, the difference is visible between the approved strike-off and the delivered garment, which shortens the conversation considerably.
Our qc team compares the first production piece against the approved strike-off before the rest of the run is released, so a drift in colour or placement is caught on one garment rather than on a full batch.
For teams comparing decoration routes, All-Over Print vs DTF vs Embroidery: Which to Choose sets out where full-garment printing fits, and What Is All-Over Print? Full-Garment Printing Explained covers the construction side.
Frequently Asked Questions
What resolution should an all-over print file be?
Between 150 and 300 dpi at final print size, checked on the largest panel of the garment. Higher numbers only help if the source detail is real, since resampling a small file does not add information.
How much bleed does full-garment printing need?
Ten to twenty millimetres beyond the cut line is the common range, with a separate seam margin sized to the seam allowance. Ask for the figure per seam type, because a flatlock join and a folded hem consume different amounts.
Can one flat artwork file be used for a full-garment print?
It can be the starting point but not the delivered file. The artwork has to be placed on each pattern piece, with the repeat aligned so the pattern continues across seams once the garment is sewn.
Should the file be RGB or CMYK?
CMYK for dye sublimation workflows, because that is the colour space the process reproduces. Supplying sRGB and letting the printer convert works only when both sides have agreed how the conversion is handled.
Why does the printed garment look different from the mockup?
A mockup shows artwork on a rendered surface, while production prints onto fabric with its own base colour, texture and absorbency. A strike-off on the production fabric is the only representation that matches the delivered piece.
What else should be checked before a bulk run?
Panel count against the construction drawing, seam alignment on a sewn sample, and the print area limits for the smallest size in the range. A file that fits a large can still run past the printable area on a small.
An all-over print file is a production document, and it should be reviewed like one. Once the panel separation, bleed and colour settings are fixed for a garment, the same template carries every future design, which is what turns full-garment printing from a custom job into a repeatable line. Fabric behaviour on the same file is covered in Sublimation Fabrics: Why Polyester Powers All-Over Print, and the inspection side is set out in Print on Demand Quality Control: What to Audit.
Related Articles
- DTF vs DTG Printing: Which Fits Your POD Store?
- How to Compare Print on Demand Suppliers in 2026
- DTF vs Sublimation vs Embroidery: Which Should You Pick?

